FE35 Grey gold belly 1957 diesel lots of work done. New tyres on rear and new wheels and tyres on front starts on battery V5 offers over £3000

MF20 baler for sale. Was working OK 2 years ago but the pick-up is broken (I think I have sourced all the parts to mend it according to my experienced engineer friend. Have decided to get a contractor to do my baling). Can load at this end. Happy to send photos or more info. Offers?

Ferguson link box £70. New Holland Super Hayliner 68 baler, barn stored £650. Houwse 5ft topper £450. Vicon Vari spreader £125.

Ferguson TED 20, late 6v 85mm bore tractor from 1951 and currently converted to 12v. Runs well on both petrol and TVO and pulls hard. Original East Sussex registration with V5c in my name. Tinwork is very straight. The engine has had a head rebuild and full service including dropping the sump to clean it all out properly. Oil pressure is where you would expect for a TED tractor but not the worst I have seen. Gearbox is tight and the hydraulics have been fully rebuilt and are strong. Rear tyres are Firestone 151 with about 50% tread and fronts are 99% tread but have a few cracks now. All round a nice little tractor and has performed well on a saw bench for the last 18 months for me, but I have bought a new project do it is time to move on. Pictures and video link available by email.

 the adjusting handle for a Mid Mounted Mower (R/H Model). Its the vertical tube which is held in position with 4 bolts. Many Thanks,

I've acquired a Ferguson loader which I am considering putting on my 1959 Mk 1 65. I want to move around a few bits and pieces, nothing arduous, but easier than using a shovel. The loader is I believe a 735 loader. It came with some separate hydraulic controls (it has three levers) which is serviced by at least three pipes. One is split (which I presume go to the rams) and I guess the other two are an out and return. Are my assumptions correct and if so where do I connect the out and return? Do I need to install a separate stop valve to a hydraulic take-off point? And if so, where would get such a acquire the stop valve? Appreciate anyone's help with this.

Looking for some solid front wheel rims for my '47 and some scalloped front rims for my '50 . Am near Plymouth but prepared to drive Cornwall or Devon to collect. Thank you.

Ferguson mid-mounted finger bar mower complete with belt and knife guards barn find £250

Ferguson Spring tine cultivator, missing one leg, needs restoration £100 ono, Ferguson tractor jack front and rear with a badge, some rot to one corner but easily fixed £100 ono, Ferguson ridger with a badge, good condition £100 Ono

Ferguson 9 tine cultivator new points and painted £225.00. Ferguson 'C' type spring tynes only , no toolbar x9 £100.00

original Massey 35/135/148 exhaust and bears the embossed triple triangle logo and MF 5. It is in very good condition and was removed from a late model 135. Can be used as is on a working tractor or sprayed white with high-temperature paint to enhance a show tractor.£300 ovno

MF 100 Series 4WD

Massey Ferguson narrow 152 vgc with V5.4 new tyers seat grill,£5500.00

Massey Ferguson 168/188 Sirocco flexi cab doors preferably good condition

Massey Ferguson PAVT 38" wheels with or without tyres & cast front wheels. Also 7.50-16 wheels.

Massey Ferguson 65 Mk 2 multi-power power steering restored a year ago everything works, great looking tractor and ready to go £5995

TE20 TVO for sale. Bought this as a non-runner last year. Great little tractor and running well everything works as it should but may need a new dynamo. Tyres good front 90% rears 50% Things were done and replaced. Head gasket done and the whole engine cleaned though while I had it apart and all tuned up. All filters changed and oil back and front end. All new electrics. New carb. New battery New water pump and thermostat New seat and exhaust kit. £1800 ONO

Massey Ferguson 158 vineyard tractor Duncan cab power steering, powerful little tractor, go straight to work or restore £3750 Ono

Breaking Ferguson TED20 for parts with cracked block Bonnet Distributor Manifold etc...

Ferguson DumpSkip HammerMill GraderBlade Transporter.

Original Hook For Ferguson Winch.

a PTO guard for a Massey 128 baler it is held on with 3bolts and covers mid bearing housing at the midpoint of the drive shaft 65353

1957 FE 35 gold grey industrial tractor rare model £5750   1952 TEF20 diesel New rad tank clutch fenders tidy tractor £2750

a complete diesel engine for an FE35 grey gold goldbelly with original paint if possible and a pair of footsteps, please ring or email

Fergie Winch, Earth Scoop, & Subsoiler (D-BE-28 or 727), and Culverwell Sack Lifter. Fergie Scoop, Dump Skip, and Crane also wanted. Also looking for a curly Hetchins racing bike!! Please email with price & photo. Thank you

Hydraulic wheel cylinders and brake shoes for Fergie TET

Require a set of rear cast centre nuts for 100/500 series. Also a pair of 9.50x16 or 11.5/80-15.3 front wheels for 590.

I am looking for a bucket for the mill loader for my TED-20 tractor.

1959 Massey Ferguson FE35 23C. Good running order. Starts on one battery. Ready to work. Also one concrete ballast weight for a T Bar and one PTO belt pulley.

Massey Ferguson 165 multi power /power steering/scirocco cab nice straight tractor /1970 J road registered £5995 Ono

Massey Ferguson 135 multi power tractor 1968 fully restored to rally condition, Goodyear rear tyres, everything works excellent condition, photos available £5,950.00

looking for an original or restored 4 wheel Hayter mower for Ferguson Tractor, must be complete can anyone help thanks very much regards Pete

1962 MF 35, 3 cylinder, been restored a year or two ago but still tidy, with as new tyres and t bar pick up hitch, lights also on the bonnet top, £4250. MF chisel plough, ( a red Bomford superflow) no welds on frame and sporting good metal £475, MF 37 flexitime cultivator with land wheels on either side and fitted with a rear crumbled roller, good bearings and very good metal, £400, front weights for 135 or 165, set of 8, £325, alloy grab handles, £135. can help with delivery.

Wanted T bar pick up hitch and tow hitch must be local to Norwich and good condition

Ford Ferguson 2 furrow plough Needs cross shaft £400 ono

steering wheel throttle assembly to suit MF 130

Ferguson Dump Skip and Fertiliser Spreader condition not important cash on collection.

Original Ferguson 35 3 cylinder bonnet hood

Bush Hogg grass topper. 5FT cutting width. Suit Ferguson TE20 or Massey Ferguson 35 tractor.

Early Ferguson finger bar mower complete. comes with original swath board and handle and original Ferguson top link. Needs a lot of TLC to bring it back up to scratch but basically sound. Included is a second, almost complete mower (same model) as spares or repair. No top link with this one. Also missing a universal joint (available around £45 I believe) and the swath board is not the original Ferguson (needs a bit of tinkering to fit). Photos available. £150 for the pair - collection only. Having a good clearout - need the space for (yet) another tractor.

Original Massey Ferguson swinging drawbar/towbar. Originally off an FE35 I believe but fitted to my TEF20 for several years with no problem (only replaced with a different type when I mounted a Cordwood saw and need to clear the pulley). Photographs available. Collection only or arrange own courier. I'm looking for £95 or very near offer.

I'm looking for a nice original and unrestored Ferguson diesel oily rag condition not too rusty cash waiting for the right tractor even a none runner