Parts for Allman speedo or to borrow to make up please knob on the side I am unsure what it does or what I am missing? Thank you

MF 590 Four-wheel drive, based in Ripley Derbys area.Later CatII axle with slim hubs.Also MF 200 Crawler non-runner, 4 in 1 bucket, spares or repair. MF 590 Swinging drawbar,80 loader boom, bucket ram and muck fork tines. Used cattle crush to fit 3 point linkage. MF 590 power steering pump

Ferguson TED20 TVO - a grey Fergie – ready for a winter restoration project Registration plate # SZ 1204 = County Down NI – but not road registered The dash serial # plate is hard to make out looks like TED 0438484 The casting # is 25.2.5 which = 25th February 1955 The serial number on the engine block is S191726E Both rear wheel axle bearings replaced by Hamilton Bros with new oil seals fitted at same time - New brake pads fitted - Hydraulics work perfectly up and down and holding New PowerSpark electronic ignition / distributor with new silicone leads & NKG sparkplugs. (Converted to negative earth) The tractor was used happily earlier this year pulling a grader and revs as shown in the videos which I can forward separately. Life still left in rear tyres but the new owner will probably wish to replace the front set. As with most TVOs the engine block has a slight crack in it – however it has been sealed – and does not affect performance. A clean and tidy machine looking for a new owner to enjoy as it is or restore further.

An engine for a Grey Ferguson TEF It must be in a good overall condition to fit my working tractor. Or somebody that can recondition my present engine, needs crankshaft regrind

Looking for a winch to fit my TEF-20

A decent Massey Ferguson 65 MK2 no rubbish, please

Rear window and glass to suit 135 Duncan cab.

Massey Ferguson rear wheel and tyre used but a good item size 12.4 32 £100 cash on collection

A set of mud scrapers for a set of 6 disc Ferguson trailing disc harrows. 4 sets one for each gang.

Grass tyres Olympic Trojan 12 4. 28 very good very little wear no cracking cash on collection only please £200 thank you

Restored red MF Fertiliser Spinner nice addition to small restored MF tractor

Swinging drawbar for 35/65, whole or parts.

Ferguson mole plough £250 good condition. Unusual Ferguson small spring-loaded ridger £180. Ferguson mounted zig zag harrows £170.

Used but working Oil Pressure Gauge and Water Temperature Gauge with Probe.

A 1949 TED20 that I am planning to leave in it's "as found" condition so shiny, bright New items would look out of place;

Buckrake Spares - has anyone got any of the linkage or other parts for a Ferguson buckrake? I am trying to build up a complete one

A saw blade guard for the Cordwood saw bench

A pair of original sidelights and plough lamp in good condition also an original steering wheel for a 35/35X.

Looking for a 6v engine for a TEA-20, good oil pressure and no cracks in the block thanks rob

Red MF Fertiliser Spreader in very good original condition, ideal implement to show & set off an original 35x or 135 or easy restoration to paint option also

Would like someone to lend me their Modified by Reekie bonnet badge ( Red badge ) so I can send to a company who is able to cast one for my Reekie, willing to pay a small fee for the loan of yours.

Ferguson narrow width petrol/TVO 1951 starts & runs well some new parts fitted, with V5 docs, with cranked hydraulic arms

FF30DS 1957 . Starts well, sounds lovely, drives well, used on road runs and attracts a lot of attention at shows. 4 new tyres, correct lights but not wired, can be seen on a recent post in 'photos' on Forum. Photos can be sent but please phone first so I know genuine interest. I have V5 in my name, very reluctant sale, tractor in South East Cornwall, asking £3200

MF35x or 135 must Be Original Or A Concourse Restoration. Good price paid for the right tractor.

Ferguson TEK-20 Petrol lovely Engine Pictures available, Good tinwork Can help with delivery £1950 ovno...

Big Bee Agri-four topper. Well made 4-foot cut, suitable for TE20, 35 or similar sized tractor, £400 ono.

Rear-wheel weights and fixings for my TEF

I’ve just purchased some Ferguson wheel girdles and I’m looking for the lugs that bolt onto them Can anyone help with this? Plus I will need a tensioning handle or would like to have a look at one so I can make one for myself

MF 200 Industrial crawler with c/weights bar, non-runner, 4 in 1 bucket, spares or repair. MF 80 Loader square type bucket, lift ram, bucket ram and two muck fork tines.MF 732 mower fingers, knife clips and ball type blade. Two Ferguson potato spinners.Good left hand 500 series door. Good 60 mower.

1 used MF 500 series radio c/w mounting box (lower mounting holes damaged)been fitted in van £25. 1 new MF 600 series radio still boxed p/n 3405062M92 with instructions £30 ono. 1 new MF 1200/1250 heater blower £30 ono. 1 new complete knotter assy for MF 120/124/128 baler £40 ono. 1 used MF 35 3cyl metal bottom hose connector £10. 1 used MF 35/135 rear wheel centre dish £25.

injector pump with injectors and pipes for M/F 135 (AD3-152)

Massey industrial 702 loader crowd rams

Massey Ferguson 1035 tractor, 4 wheel drive, power steering, roll bar, v5 logbook, 2880 genuine hours, on turf tyres, creep gear, lights all working A lovely genuine and tidy little tractor, about the same physical size as a 35 Can send pictures no problem £5750.00

Would anybody be interested in my Fergie TED 20 TVO - I've spent some money fixing the real wheel bearings and seals so that's good and I converted the dissy to PowerSpark electronic ignition with negative earth. I did use it for a day on TVO grading my road - and then before switch off back to petrol - but it has not started since. I've checked all the usual things - timing, spark plugs, air and petrol flow (via a replacement new Zenith Carb) but to no avail. The plugs and getting wet and petrol is coming out the bottom of the carb after a while. If I take plugs out and let them dry - I get a momentary splutter but as soon as the choke is released the engine stops and will not start. It was going to be a restoration project - but I've bought a 35 instead which works just fine. Any ideas or suggestions gratefully received. Or is it time to convert to a Perkins or indeed other cast iron engine?

Bonnet belt guards, these bolt to the side of the Ferguson 20 bonnet

Ferguson 2 furrow semi digger plough complete with skimmer's furrow wheel and adjuster

Horn Draulic Loader off FE35 with the bucket. New ram seals and pipes £300 Ono

Ferguson Banana loader frame (frame only). Little surface rust but in good condition No bends or cracks

Looking for someone to maintain our MF135 as in service and repair as necessary.

Any information relating to the Ferguson T20 low ground clearance (golf course) conversion. I own one and would like to know more about it, for example, who did the conversions?

Massey Ferguson 35 Tractor 3 Cylinder Low hours Start runs and drives well. Good starter with no smoke. Engine runs nice and even with good oil pressure and is responsive. Clutch and brakes work fine with no problems getting any gear. Pto and hydraulics work fine as does the tipping pipe. Front tyres good rears plenty of tread. It’s fitted with a Lambourn cab which is complete and in excellent rot free condition with solid wings. Good cladding with all plastic windows intact and clear to see through the roll down back window is all there and in good order. All the trim and paintwork is exceptionally good original rot free and straight. A trailer hook is also fitted. New battery fitted. V5 road registered